microSD and internal Flash Mass Storage for Blockheads and Fatties
Intro
Raw blocks or filesystem? A real filesystem is hefty and several times larger than the Forth kernel itself. But if you really want to exchange data with other systems, you need some sort of compatible storage medium like a microSD with a FAT filesystem. Or if you want to use your embedded system as a stand-alone development system and save the source code.

For a stand-alone Forth system, especially a embedded system, a block storage (on internal Flash or external Media) or no mass storage at all fill the bill.

nucleo-dongle-sdcard2.jpg
microSD adapter

Hardware

Flash Drive

Built-in flash

The built-in flash (STM32WB55C has 1 MiB FLASH, page size 4 KiB) can be used as a flash drive. No additional hardware is needed. 384 KiB is about the same as the old DD 5 1/4" floppy from 1978 had. The STM32F403 has also 1 MiB flash, but most sectors are 128 KiB, and the built-in flash is therefore not suitable for a flash drive.

Flash Memory Layout

FLASH (rx)                 : ORIGIN = 0x08000000, LENGTH = 256K
   20 KiB Forth Core
   140 KiB Middleware (debug 210 KiB)

FLASH_FORTH (rx)           : ORIGIN = 0x08040000, LENGTH = 128K
   128 KiB Flash Dictionary

FLASH_DRIVE (rx)           : ORIGIN = 0x08060000, LENGTH = 384K
   384 KiB future use for built in flash drive

FLASH_BLESTACK (rx)        : ORIGIN = 0x080C0000, LENGTH = 256K

Create a 384 KiB FAT filesystem as a loop device on Linux (or use the already prepared fd-384k.img):

$ dd if=/dev/zero of=fd-384k.img bs=512 count=768
768+0 Datensätze ein
768+0 Datensätze aus
393216 bytes (393 kB, 384 KiB) copied, 0,00155426 s, 253 MB/s
# losetup /dev/loop1 fd-384k.img
# mkfs -t vfat /dev/loop1
# mount -o loop /dev/loop1 /mnt

Copy the the files and directories with cp or tar to the mounted image, e.g.

# cd sdcard
# tar cf - etc fsr home man README.md | tar xvf - -C /mnt
# umount /mnt

Umount the loop-device and copy the file to a SD-card.

Copy the filesystem to the flash disk on the target Mecrisp-Cube system:

dd 1:/boot/fd-384k.img 0:

Serial Flash

STM32F405 Feather (SPI W25Q16)

The STM32F405 Feather has a 2 MiB Serial Flash W25Q16 on board. The smallest erasable chunk of data is the 4 KiB sector. But the default FAT block is 512 Bytes, that means if you want to write something to a not erased block, you have to erase the whole sector. For this the sector has to be buffered in RAM. For details see:

You can use the local CLI commands like mkfs, mkdir and cp to populate the serial flash with files and directories. But this is tedious job because there is no recursive copy. It is easier to use a real GNU/Linux for this.

Create a 2 MiB FAT filesystem as a loop device on Linux (or use the already prepared fd-2MiB.img):

$ dd if=/dev/zero of=fd-2MiB.img bs=512 count=4096
# losetup /dev/loop1 fd-2MiB.img
# mkfs -t vfat /dev/loop1
# mount -o loop /dev/loop1 /mnt

Copy the the files and directories with cp or tar to the mounted image, e.g.

# cd sdcard
# tar cf - etc fsr home man README.md | tar xvf - -C /mnt

Umount the loop-device and copy the file to a SD-card.

Copy the filesystem to the flash disk on the target Mecrisp-Cube F405 system:

dd 1:/boot/fd-2MiB.img 0:

serial-flash.jpg
Serial Flash on Board
W25Q16.png
SPI Interface

The SST25VF016B seems to be compatible.

STM32WB5MM Discovery Kit (QSPI S25FL128)

16 MiB Quad SPI NOR Flash chip S25FL128SDSMFV001. Uniform 64-KB sectors with Hybrid 4-KB sectors.

The main flash array is divided into erase units called sectors. The sectors are organized either as a hybrid combination of 4-KB and 64-KB sectors, or as uniform 256-KB sectors.

32 4 KiB sectors and 254 64 KiB sectors. What a pain, why use STM this Flash? To simplify writing, only the first 4 KiB of the 64 KiB sectors are used. That means (32 + 254) * 4 KiB = 1140 KiB are available for the volume. To make it even simpler, I use only 64 KiB sectors, that means there are 256 sectors and therefore 1 MiB available for the volume. For implementation see fd.c and fd_spi.c

Create a 1 MiB FAT filesystem as a loop device on Linux (or use the already prepared fd-1MiB.img):

$ dd if=/dev/zero of=fd-1MiB.img bs=512 count=2048
# losetup /dev/loop1 fd-1MiB.img
# mkfs -t vfat /dev/loop1
# mount -o loop /dev/loop1 /mnt

Copy the the files and directories with cp or tar to the mounted image, e.g.

# cd sdcard
# tar cf - etc fsr home man README.md | tar xvf - -C /mnt

Umount the loop-device and copy the file to a SD-card.

Copy the filesystem to the flash disk on the target Mecrisp-Cube WB5M Discovery system:

dd 1:/boot/fd-1MiB.img 0:

STM32WB Feather (SPI W25Q128)

The W25Q128JVPIQ. There are 4,096 erasable 4 KiB sectors. That means 16 MiB are available for the volume.

Create a 16 MiB FAT filesystem as a loop device on Linux (or use the already prepared fd-16MiB.img):

$ dd if=/dev/zero of=fd-16MiB.img bs=512 count=32768
# losetup /dev/loop1 fd-16MiB.img
# mkfs -t vfat /dev/loop1
# mount -o loop /dev/loop1 /mnt

Copy the the files and directories with cp or tar to the mounted image, e.g.

# cd sdcard
# tar cf - etc fsr home man README.md | tar xvf - -C /mnt

Umount the loop-device and copy the file to a SD-card.

Copy the filesystem to the flash disk on the target Mecrisp-Cube WB Feather system:

dd 1:/boot/fd-16MiB.img 0:

STM32H743 Nucleo (QSPI W25Q128)

There is no serial NOR flash on board, but there is an QSPI interface on connector CN10.

It is easy to connect a MIKROE-4067 or Sparkfun SPX-17115 with a W25Q128JV (128M-bit) NOR flash memory on it. See also Winbond W25Q128JVPIQ.

The driver (fd_spi.c, fd.c) is based on the STM example project for the N25Q128A

There are 4,096 erasable 4 KiB sectors. That means 16 MiB are available for the volume.

Name Port Nucleo MIKROE-4067 SPX-17115
QS_CS PG6 CN10.13 CS 2 QSPI-CS
QS_CS PB10 CN10.32 CS 2 QSPI-CS
QS_CLK PB2 CN10.15 CLK 3 QSPI-CLK
GND   CN10.17 GND 8 GND
QS_D3 PD13 CN10.19 IO3 7 QSPI3
QS_D1 PD12 CN10.21 MISO SDO 5 QSPI1
QS_D0 PD11 CN10.23 MOSI ŜDI 4 QSPI0
QS_D2 PE2 CN10.25 IO2 6 QSPI2
+3.3V   CN8.7 +3.3V 1 3.3V

Copy the filesystem to the flash disk on the target Mecrisp-Cube STM32H743 Nucleo system:

dd 1:/boot/fd-16MiB.img 0:

See above (MicroSdBlocks#STM32WB_Feather_SPI_W25Q128) for creating the image fd-16MiB.img.

Arduino Portenta H7 (QSPI MX25L12833F)

The Macronix MX25L12833F is compatible to the Winbond W25Q128JVPIQ. See above MicroSdBlocks#STM32H743_Nucleo_QSPI_W25Q128 for details.

SD Drive

Home Brewed microSD Adapter for STM32WB55 Nucleo/Dongle (SPI)

You can build a very cheap microSD adapter by yourself with a microSD to SD adapter. You have to solder only 7 wires to a pin header. The breakout board for microSD cards from Adafruit have a level shifter, but this is not needed because the levels on the Nucleo are already 3.3 V. Only the CD pin is missing, this could be handy to detect a microSD card.

MMC-SD-miniSD-microSD-Color-Numbers-Names.gif nucleo-sd-adapter.jpg

SD pin microSD pin Name Description Arduino/Nucleo Pin Nucleo Dongle
1 2 nCS Card Select [CS] D10 (1) PB2 CN1.7
2 3 DI Serial Data In [MOSI] D11 (2) PA7 CN1.10
3 - VSS Ground GND (5) GND CN1.1
4 4 VDD Power 3.3 V 3V3 (6) 3V3 CN1.6
5 5 CLK Serial Clock [SCLK] D13 (4) PA5 CN1.8
6 6 VSS Ground GND (5) GND CN1.1
7 7 DO Serial Data Out [MISO] D12 (3) PA6 CN1.9
8 8 NC Unused    
9 1 NC Unused    

Block size 512 Bytes, SPI mode 0 (CPHA=0, CPOL=0), Pull-up on MISO.

nucleo-sd-adapter.jpg

microSD Adapter on STM32F405 Feather (SDIO)

SDIO Interface is well supported by the STM32F405, there is no need to use the slower SPI.

sd-socket.jpg
microSD socket
sdio-schematic.png
SDIO Interface

Home Brewed microSD Adapter for the STM32H743 Nucleo (SDMMC)

SDIO (SDMMC) Interface is well supported by the STM32H74x, there is no need to use the slower SPI.

SD pin microSD pin Name SPI Name SDMMC Nucleo Pin CN8
1 2 nCS SDIO_D3 8
2 3 DI SDIO_CMD 12
3 - VSS GND 11
4 4 VDD VDD 7
5 5 CLK SDIO_CLK 10
6 6 VSS GND 11
7 7 DO SDIO_D0 2
8 8 NC SDIO_D1 4
9 1 NC SDIO_D2 6

Home Brewed microSD Adapter for the Feather Boards

SD pin microSD pin Name Description Feather Pin
1 2 nCS Card Select [CS] D10
2 3 DI Serial Data In [MOSI] MO (D4)
3 - VSS Ground GND
4 4 VDD Power 3.3 V 3V3
5 5 CLK Serial Clock [SCLK] SCK (D2)
6 6 VSS Ground GND
7 7 DO Serial Data Out [MISO] MI (D3)
8 8 NC Unused  
9 1 NC Unused  

JTAG/SWD

JTAG Pin JTAG STM 14pin CN1 Dongle CN2 Dongle Description
  1     NC
  2     NC
1 3 6   VDD
2 4 3   SWDIO
3 5 1   GND
4 6 4   SWCLK
5 7 1   GND
6 8 5   SWO
7 9     NC
8 10     NC
9 11 1   GND_DETECT
10 12 2   NRST
  13   7 (PB7) VCP_RX Target
  14   6 (PB6) VCP_TX Target

FAT Filesystem

FAT is the de-facto standard for embedded systems and mobile devices. The FAT filesystem for Mecrisp-Cube is based on FatFs - Generic FAT Filesystem Module and supports FAT (12, 16, and 32) and exFAT formatted SD cards.

Forth source files. I propose .fs extension for Forth source files the same as GForth does. But anyway you can use what you want (.f, .4th, .fth, etc).

include   ( i*x "name" -- j*x )      Interprets the content of the file <name>. 
included  ( i*x c-addr u -- j*x )    Interprets the content of the file.

coredump  ( "name" -- )      Dumps the flash memory (core) into the file <name>.

user variables which contain file desciptor (pointer address a to file object structure)
stdin     ( -- a )           for fs-emit and fs-emit?
stdout    ( -- a )           for fs-key and fs-key?
stderr    ( -- a )           not used yet

fs-emit   ( c -- )           Emits a character c to a file (stdout)
fs-emit?  ( -- ? )           Ready to send a character to a file? (stdout)
fs-key    ( -- c )           Waits for and fetches a character from file. <0 for EOF or error. (stdin)
fs-key?   ( -- ? )           Checks if a character is remaining (stdin)

Words from redirection.fs

>f_open   ( a1 a2 -- ior )   open a file a1 to redirect to a2 (emit, type, ...)
>>f_open  ( a1 a2 -- ior )   open a file to redirect to (emit, type, ...). Append to file
>file     ( -- a1 a2 )       redirect to a file (emit, type, ...)
>f_close  ( -- ior )         close redirection to file 
<f_open   ( a1 a2 -- ior )   open a file to redirect from (key, accept, ...)
<file     ( -- a1 a2)        redirection from a file (key, accept, ...)
<f_close  ( -- ior )         close redirection from file 

>term     ( a1 a2 -- )       terminate to-file redirection
<term     ( a1 a2 -- )       terminate from-file redirection
<>term    ( a1 a2 a3 a4 -- ) terminate redirection

>uart     ( -- a1 a2 )       redirection to uart
<uart     ( -- a1 a2 )       redirection from uart (key, accept, ...)
<>uart    ( -- a1 a2 a3 a4 ) redirection from and to uart

>cdc      ( -- a1 a2 )       redirection to cdc (USB serial)
<cdc      ( -- a1 a2 )       redirection from cdc (key, accept, ...)
<>cdc     ( -- a1 a2 a3 a4 ) redirection from and to cdc

>crs      ( -- a1 a2 )       redirection to crs (BLE serial)
<crs      ( -- a1 a2 )       redirection from crs(key, accept, ...)
<>crs     ( -- a1 a2 a3 a4 ) redirection from and to crs

>oled     ( -- a1 a2 )       redirection to oled

>plex     ( -- a1 a2 )       redirection to plex LED display

Words from conditional.fs. See also https://forth-standard.org/standard/tools.

query not working in include! All the conditionals have to be on the same line.

[IF]      ( flag | flag "<spaces>name ..." -- )  If flag is true, do nothing. Otherwise parse and discard words from the parse area 
[ELSE]    ( "<spaces>name ..." -- )              Parse and discard words from the parse area
[THEN]    ( -- )                                 Does nothing. [THEN] is an immediate word. 
[ENDIF]   ( -- )                                 Does nothing. [ENDIF] is an immediate word. 
[IFDEF]   ( "<spaces>name ..." -- )              If the name can be found, do nothing. Otherwise parse and discard words from the parse area
[IFNDEF]  ( "<spaces>name ..." -- )              If the name can´t be found, do nothing. Otherwise parse and discard words from the parse area
[DEFINED] ( "<spaces>name ..." -- flag )         Return a true flag if name is the name of a word that can be found
[UNDEFINED] ( "<spaces>name ..." -- flag )       Return a false flag if name is the name of a word that can be found

Filesystem API

Some File Operation Basics

The C function prototype for f_open looks like this:

FRESULT f_open (
  FIL* fp,           /* [OUT] Pointer to the file object structure */
  const TCHAR* path, /* [IN] File name */
  BYTE mode          /* [IN] Mode flags */
);

The parameter order for the Forth Word is the same: addr1 is address of the file object data structure FIL, addr2 is the address of the filename array (0 terminated string).

f_open  ( addr1 addr2 u -- ior )   opens a file.

The FIL data structure can be created as follows:

create fil /FIL allot ok.

See also f_open.

Print current directory:

256 buffer: path[RET] ok.
path 256 f_getcwd drop strlen type[RET] 0:/ ok.
or easier with unix like command pwd:
pwd[RET]
0:/ ok.

Change current directory

path 256 accept[RET] common[RET]  ok.
path swap 2dup str0term drop f_chdir .[RET] 0 ok.
pwd[RET]
0:/common ok.

path dup .str" /fsr" f_chdir .[RET] 0 ok.
pwd[RET]
0:/fsr ok.

Change drive (if you have a microSD connected):

chdrv 1:[RET]
ok.
pwd[RET]
1:/ ok.
cd home[RET] 
 ok.
pwd[RET] 
1:/home ok.
0:[RET]  ok.
pwd[RET] 
0:/fsr ok.

File Redirection

There are many Forth words to format a string e.g. emit, type or print something to the console. It is also possible to fetch user input like key, accept, etc. All these words can be used on files. Nothing new for a UNIX user. Mecrisp use hooks for redirection terminal IO, these hooks can also be used for file redirection.

Step by Step Redirection to a File

Sample to use hook-emit for redirection output from ls -l to a file.

Open file test.tmp

path .str" test.tmp[RET] ok.
fil path FA_WRITE FA_OPEN_ALWAYS + f_open .[RET] 0 ok.

Save file descriptor to stdout user variable

fil stdout ![RET] ok.

Push current hook to the stack

hook-emit @[RET] ok.

Redirect emit to fs-emit (there is no ok.)

' fs-emit hook-emit ! [RET]

Type ls -l, there is no echo on the console

ls -l[RET]

Restore old hook:

hook-emit ! [RET] ok.

Close file

fil f_close .[RET] 0 ok.

Show the contents of the file test.tmp

cat test.tmp[RET]

drw-         0 2021-03-06T14:36:40 man
drw-         0 2021-03-06T14:36:40 fsr
-rwa      7219 2021-03-06T14:04:12 README.md
drw-         0 2021-03-26T18:47:12 boot
drw-         0 2021-04-18T17:40:14 etc
drw-         0 2021-03-06T14:36:40 home
-rwa         0 2000-01-01T00:11:12 test.tmp
 ok.
hook-emit !   ok.

Redirection the Easy Way

create fil /FIL allot
256 buffer: path
path .str" test.tmp"
fil path >f_open drop
>file ls -l
>term
>f_close drop

Some helper words in redirection.fs

: >f_open ( addr c-addr -- ior )  \ open a file to redirect to (emit, type, ...)
  swap dup stdout ! swap
  FA_WRITE FA_OPEN_ALWAYS + f_open 
;

: >>f_open ( addr c-addr -- ior )  \ open a file to redirect to (emit, type, ...). Append to file
  swap dup stdout ! swap
  FA_WRITE FA_OPEN_APPEND + f_open 
;

: >file ( -- addr1 addr2 )  \ redirect to a file (emit, type, ...)
  hook-emit @  
  hook-emit? @
  ['] fs-emit hook-emit !
  ['] fs-emit? hook-emit? !
;

: >term ( addr1 addr2 -- )   \ terminate to-file redirection
  hook-emit? ! 
  hook-emit ! 
;
: >f_close ( -- ior )
  stdout @ f_close
  0 stdout !
;

: <f_open ( addr1 c-addr -- ior )  \ open a file to redirect from (key, accept, ...)
  swap dup stdin ! swap
  FA_READ f_open
;

: <file ( -- addr2 addr3)  \ redirection from a file (key, accept, ...)
  hook-key @  
  hook-key? @  
  ['] fs-key hook-key !
  ['] fs-key? hook-key? !
;

: <term ( addr1 addr2 -- )   \ terminate from-file redirection
  hook-key? ! 
  hook-key ! 
;

: <f_close ( -- ior ) 
  stdin @ f_close
  0 stdin !
;

INCLUDE on Startup

The file 0:/etc/rc.local is included on the startup:

\ this file will be included on startup
cr .( include 0:/etc/rc.local ) cr
.time cr
watchdog? [IF] .( Watchdog has bitten, # bites: ) watchdog# . cr [THEN]
assert?   [IF] assert@ hex. .assert cr [THEN]

https://github.com/spyren/Mecrisp-Cube/blob/master/sdcard/etc/rc.local

Data Structures

FATFS

Only used in FS_init(). We have only two drives. For details see FATFS

/FATFS ( -- u )   Gets the FATFS structure size

FIL

For details see FIL.

/FIL              ( -- u ) Gets the FIL structure size

FA_READ           ( -- u ) Gets the Mode Flag FA_READ
FA_WRITE          ( -- u ) Gets the Mode Flag FA_WRITE
FA_OPEN_EXISTING  ( -- u ) Gets the Mode Flag FA_OPEN_EXISTING
FA_CREATE_NEW     ( -- u ) Gets the Mode Flag FA_CREATE_NEW
FA_CREATE_ALWAYS  ( -- u ) Gets the Mode Flag FA_CREATE_ALWAYS
A_OPEN_ALWAYS     ( -- u ) Gets the Mode Flag FA_OPEN_ALWAYS
FA_OPEN_APPEND    ( -- u ) Gets the Mode Flag FA_OPEN_APPEND

POSIX FatFs
"r" FA_READ
"r+" FA_READ FA_WRITE or
"w" FA_CREATE_ALWAYS FA_WRITE or
"w+" FA_CREATE_ALWAYS FA_WRITE or FA_READ or
"a" FA_OPEN_APPEND FA_WRITE or
"a+" FA_OPEN_APPEND FA_WRITE or FA_READ or
"wx" FA_CREATE_NEW FA_WRITE or
"w+x" FA_CREATE_NEW or FA_WRITE FA_READ or

DIR

For details see DIR.

/DIR         ( -- u ) Gets the DIR structure size

FILINFO

For details see FILINFO.

/FILINFO     ( -- u ) Gets the FILINFO structure size

fsize+       ( -- u ) Gets the FILINFO structure fsize offset
fdate+       ( -- u ) Gets the FILINFO structure fdate offset
ftime+       ( -- u ) Gets the FILINFO structure ftime offset
fattrib+     ( -- u ) Gets the FILINFO structure fattrib offset
fname+       ( -- u ) Gets the FILINFO structure fname offset
altname+     ( -- u ) Gets the FILINFO structure altname offset

File Access Functions/Words

Directory Access Functions/Words

File and Directory Management Functions/Words

  • f_stat - Check existance of a file or sub-directory
  • f_unlink - Remove a file or sub-directory
  • f_rename - Rename/Move a file or sub-directory
  • f_chmod - Change attribute of a file or sub-directory
  • f_utime - Change timestamp of a file or sub-directory
  • f_mkdir - Create a sub-directory
  • f_chdir - Change current directory
  • f_chdrive - Change current drive
  • f_getcwd - Retrieve the current directory and drive

Volume Management and System Configuration Functions/Words

  • f_mount - Register/Unregister the work area of the volume
  • f_mkfs - Create an FAT volume on the logical drive
  • f_fdisk - (Create partitions on the physical drive)
  • f_getfree - Get free space on the volume
  • f_getlabel - Get volume label
  • f_setlabel- Set volume label

UNIX like Shell Commands

Do not expect real UNIX commands not even comparable to the Busybox commands. The UNIX like shell commands are parsing words. The parameters are parsed from the input stream till the end of line. These commands are not intended to use in other words, they are used in the interpreter mode (run-time), use f_ words in compiler mode. Spaces in path und file names are not allowed. Verly limited wildcards (only * and ?) for ls. No standard input/ouptut/err redirection.

Shell Prompt

: init ;

: prompt ( -- ) 
  begin 
    tib 256 f_getcwd drop strlen type \ show current working directory
    ."  > "    \ show ">" for prompt. Could show "OK."
    query interpret cr 
  again
;
 
: init init ['] prompt hook-quit ! ; \ make new prompt 
 
init quit

Forth String to 0-Terminated String and vice versa

Caution! There must be space for the 0 character at the end of the string.
: str0term ( cadr len -- cadr len )
  + 0 swap c!
;

strlen ( cadr -- cadr len )  \ 0-Terminated String to Forth String

Commands

  • ls [-a] [-l] [-1] [FILE]
       -a show hidden files
       -l use a long listing format
       -1 list one file per line
    
    ls ( "line<EOL>" -- )  list directory contents
    
  • pwd
    pwd ( -- )  print name of current/working directory
    
  • cd [DIR]
    
    cd ( "line<EOL>" -- )  change the working directory
    
  • chdrv [0:|1:|FD:|SD:]
    
    chdrv ( "line<EOL>" -- )  changes the current drive.
    
  • cat [-n] [> NEWFILE] [>> FILE] [<< EOF] FILES...
       -n line numbers
       > redirect output to NEWFILE
       >> redirect output and append to FILE
       << redirect input till EOF
    
    cat ( "line<EOL>" -- )  concatenate files and print on the console
    
  • mkdir [DIR]...
    
    mkdir ( "line<EOL>" -- )  make directories
    
  • rm FILE...
    
    rm ( "line<EOL>" -- )  remove files or directories
    
  • mv SOURCE DEST
    
    mv ( "line<EOL>" -- )  move (rename) files
    
  • cp SOURCE DEST
    
    cp ( "line<EOL>" -- )  copy files
    
  • chmod [-a] [+l] [=1] FILE...
       -rwa selected file mode bits removed 
       +rwa selected file mode bits added 
       =rwa selected file mode bits set 
    
    chmod ( "line<EOL>" -- )  change file mode bits
    
  • touch FILE...
       -c do not create any files
    
    A FILE argument that does not exist is created empty.
    
    touch ( "line<EOL>" -- )  change file timestamps 
    
  • df [VOLUME]
    
    df ( "line<EOL>" -- )  report file system disk space usage (1 KiB blocks)
    
  • du [FILE]
       -h print sizes in powers of 1024 (e.g., 1023 MiB)
    
    du ( "line<EOL>" -- )  estimate file space usage
    
  • vol [-d NUMBER] [-n NAME]
       -d drive number
       -n change drive name to NAME
    
    vol ( "line<EOL>" -- )  get and set volume label
    
  • mount [0:|1:|FD:|SD:]
     
    mount ( -- )  mount default drive
    
  • umount [0:|1:|FD:|SD:]
     
    umount ( -- )  unmount default drive
    
  • vi [-R] [-h] [-c <COLUMNS>] [-r <ROWS>] [FILE]
       -h show features
       -R Read-only mode. You can still edit the buffer, but will be prevented from overwriting a file.
       -e erase the text buffer
       -c <COLUMNS> screen columns, range 40..128 default 80
       -r <ROWS> screen rows, range 16..30 default 24
    
    vi ( "line<EOL>" -- )  a (Forth) programmer's text editor
    
  • split [-l NUMBER] FILE
       -l NUMBER  put NUMBER lines/records per output fileline numbers (default 1000 lines)
    
    suffix length is only 1, generated file names are like this: xa, xb, xc, ...
    split ( "line<EOL>" -- )  split a file into pieces
    
  • wc FILE...
    
    wc ( "line<EOL>" -- )  Word count, print newline, word, and byte counts for each file
    
  • mkfs [-f FAT|FAT32|EXTFAT] 0:|1:
       -f FAT type
    
    mkfs ( "line<EOL>" -- )  make a filesystem
    
  • dd 0:|FILE FILE|0:
    
    dd ( "line<EOL>" -- )  Convert and copy files (Disk Destroyer :-)
    
  • coredump [-a] FILE
       -a dump everything (768 KiB)
    coredump ( "line<EOL>" -- )  dump the flash contents (flash dictionary) to a file
    

  • less
  • fdisk
  • date
  • ps -> .threads
  • kill

C-String Helpers

Middleware like FatFs and RTOS expect C strings (see null-terminated string). In Forth, the preferred representation of strings on the stack is c-addr u-count, where c-addr is the address of the first character and u-count is the number of characters in the string.
str0term     ( c-addr len -- )          make Forth string null-terminated, be sure the buffer is long enough to accept an additional 0 character.
strlen       ( c-addr -- c-addr len )   calculate the length of a C string, Forth string compatible
.str"        ( c-addr "text" --  )      copy string into buffer. String is null-terminated
s0"          ( "text" -- c-addr len )   Compiles a 0-terminated string and gives back its address and length when executed
                                        similar to s" but with 0-termination
.(           ( "text) --  )             Mecrisp's ." is working only in compile mode

Raw Blocks

Flash Drive

The Flash on the STM32WB is divided in 4 KiB pages. For 1 KiB blocks the other 3 KiB in the page have to be buffered.

SD Drive

One Forth block consists of two microSD sectors. No filesystem is involved, blocks are mapped direct to the sectors: block_number = sector_number / 2. Caution! If you write a block on a formatted disk you will destroy the filesystem. Block 0 for example is the Master Boot Sector, to overwrite this sector/block would end in a disaster. If you really want to share blocks and filesystem on the same disk you have to create an additional partition for the Forth blocks. Or if you only want to play with some toy blocks, you can abuse the boot loader, because it is usually not required and you can therefore use blocks from 10 to 100. But be warned, do not do this on the SD card with the vacation pictures!

The blocks can be used as buffers. As long as you use less or equal than 4 blocks, nothing is stored on the SD card.

Block (Virtual Memory) Words

block          ( n -- a )      Return address of buffer for block n. 0 on error.
buffer         ( n -- a )      Return address of buffer for block n. Does not get the block from disk. 0 on error.
empty-buffers  ( -- )          Marks all block buffers as empty.
update         ( -- )          Marks most recent block as updated (dirty).
save-buffers   ( -- )          Transfers the contents of each updated block buffer to disk.
flush          ( -- )          save-buffers empty-buffers
list           ( n -- )        Display block n. The block is displayed as 16 numbered lines, each of 64 characters. 
load           ( n -- )        Interprets the content of block n. 

drive          ( u -- )        Initializes the drive (0 flash drive, 1 SD drive) and makes it current, sets the block count.
#blocks        ( -- n )        Gets the block count from current drive.
erasedrv       ( -- )          Erase current Drive (Chip Erase)

Block Editor

VI or EMACS keybindings? VI has a line editing mode too, fine for really dumb terminals.

Raw Blocks and GNU/Linux

Example 2 GiB microSD FAT16 formatted, show the disk parameter with fdisk:

# fdisk /dev/sdf
...
Befehl (m für Hilfe): p
Festplatte /dev/sdf: 1,91 GiB, 2032664576 Bytes, 3970048 Sektoren
Festplattenmodell: FCR-HS219/1     
Einheiten: Sektoren von 1 * 512 = 512 Bytes
Sektorgröße (logisch/physikalisch): 512 Bytes / 512 Bytes
E/A-Größe (minimal/optimal): 512 Bytes / 512 Bytes
Festplattenbezeichnungstyp: dos
Festplattenbezeichner: 0x00000000

Gerät      Boot Anfang    Ende Sektoren Größe Kn Typ
/dev/sdf1          249 3967487  3967239  1,9G  6 FAT16

Fill the SD with zeros (1'000'000 sectors à 512 Bytes), that takes about 5 Minutes:

# dd if=/dev/zero of=/dev/sdf  count=1000000
1000000+0 Datensätze ein
1000000+0 Datensätze aus
512000000 Bytes (512 MB, 488 MiB) kopiert, 271,43 s, 1,9 MB/s

Write the first block with the famous F example letter-f.block from Starting Forth, Leo Brodie:

# dd if=letter-f.block of=/dev/sdf
2+0 Datensätze ein
2+0 Datensätze aus
1024 Bytes (1,0 kB, 1,0 KiB) kopiert, 0,00226272 s, 453 kB/s
Put the microSD card into the SD adapter and startup the Mecrisp-Cube Nucleo:
Mecrisp-Cube 1.2.0 for STM32WB55 (C) peter@spyr.ch.
Based on Mecrisp-Stellaris 2.5.2 by Matthias Koch. 
0 list 
Block# 0 
  0 \ Large letter F                                                
  1 : STAR    [CHAR] * EMIT ;                                       
  2 : STARS   0 DO  STAR  LOOP ;                                    
  3 : MARGIN  CR 30 SPACES ;                                        
  4 : BLIP    MARGIN STAR ;                                         
  5 : BAR     MARGIN 5 STARS ;                                      
  6 : F       BAR BLIP BAR BLIP BLIP CR ;                           
  7                                                                 
  8 F                                                               
  9                                                                 
 10                                                                 
 11                                                                 
 12                                                                 
 13                                                                 
 14                                                                 
 15                                                                 
 ok.
0 load 
                              *****
                              *
                              *****
                              *
                              *
 ok.
 ok.
0 block hex. 200216F8  ok.
0 block 1200 dump 
200216F0 :  00 01 00 00 D9 86 03 00   5C 20 4C 61 72 67 65 20  | ........  \ Large  |
20021700 :  6C 65 74 74 65 72 20 46   20 20 20 20 20 20 20 20  | letter F           |
20021710 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
20021720 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
20021730 :  20 20 20 20 20 20 20 20   3A 20 53 54 41 52 20 20  |           : STAR   |
20021740 :  20 20 5B 43 48 41 52 5D   20 2A 20 45 4D 49 54 20  |   [CHAR]   * EMIT  |
20021750 :  3B 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  | ;                  |
20021760 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
20021770 :  20 20 20 20 20 20 20 20   3A 20 53 54 41 52 53 20  |           : STARS  |
20021780 :  20 20 30 20 44 4F 20 20   53 54 41 52 20 20 4C 4F  |   0 DO    STAR  LO |
20021790 :  4F 50 20 3B 20 20 20 20   20 20 20 20 20 20 20 20  | OP ;               |
200217A0 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
200217B0 :  20 20 20 20 20 20 20 20   3A 20 4D 41 52 47 49 4E  |           : MARGIN |
200217C0 :  20 20 43 52 20 33 30 20   53 50 41 43 45 53 20 3B  |   CR 30   SPACES ; |
200217D0 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
200217E0 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
200217F0 :  20 20 20 20 20 20 20 20   3A 20 42 4C 49 50 20 20  |           : BLIP   |
20021800 :  20 20 4D 41 52 47 49 4E   20 53 54 41 52 20 3B 20  |   MARGIN   STAR ;  |
20021810 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
20021820 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
20021830 :  20 20 20 20 20 20 20 20   3A 20 42 41 52 20 20 20  |           : BAR    |
20021840 :  20 20 4D 41 52 47 49 4E   20 35 20 53 54 41 52 53  |   MARGIN   5 STARS |
20021850 :  20 3B 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |  ;                 |
20021860 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
20021870 :  20 20 20 20 20 20 20 20   3A 20 46 20 20 20 20 20  |           : F      |
20021880 :  20 20 42 41 52 20 42 4C   49 50 20 42 41 52 20 42  |   BAR BL  IP BAR B |
20021890 :  4C 49 50 20 42 4C 49 50   20 43 52 20 3B 20 20 20  | LIP BLIP   CR ;    |
200218A0 :  20 20 20 20 20 20 20 20   20 20 20 20 20 20 20 20  |                    |
...
20021AF0 :  20 20 20 20 20 20 20 20   00 00 00 00 01 00 00 00  |           ........ |
...
20021BB0 :  00 00 00 00 00 00 00 00   00 00 00 00 00 00 00 00  | ........  ........ |
 ok.

Simple Block Operations

Init flash drive

0 drive[RET] ok.
#blocks .[RET] 16384  ok.
erasedrv [RET] ok.

there are 16384 blocks, this means 16 MiB.

get the address of block 100 and write "Hallo Velo"

100 buffer hex.[RET] 24017588  ok.
100 block .str" Hallo Velo"[RET]  ok.
100 block strlen type[RET] Hallo Velo ok.

Save Block 100 to the disk:

update save-buffers[RET]  ok.

Restart the Forth System (power cycle, reset, or Ctrl-C):

Mecrisp-Cube 1.4.4 for STM32H743, 256/1024 KiB RAM/FLASH dictionary (C) 2022 peter@spyr.ch
  * Firmware Package STM32Cube H7 V1.10.0, USB-CDC (C) 2021 STMicroelectronics
  * CMSIS-RTOS V2 FreeRTOS wrapper, FreeRTOS Kernel V10.3.1 (C) 2020 Amazon.com
  * FatFs for internal flash and microSD - Generic FAT fs module  R0.12c (C) 2017 ChaN
  * tiny vi - part of BusyBox (C) 2000, 2001 Sterling Huxley
0:/etc/rc.local: can't find file
0 drive[RET] ok.
100 block strlen type[RET] Hallo Velo ok.

-- Peter Schmid - 2020-06-03

Creative Commons License
This work by Peter Schmid is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Topic attachments
I Attachment History Action Size Date Who Comment
GIFgif MMC-SD-miniSD-microSD-Color-Numbers-Names.gif r1 manage 19.7 K 2020-06-03 - 07:39 PeterSchmid  
PNGpng W25Q16.png r1 manage 5.7 K 2021-03-30 - 13:38 PeterSchmid  
Unknown file formatblock letter-f.block r1 manage 1.0 K 2020-06-12 - 19:46 PeterSchmid  
JPEGjpg nucleo-dongle-sdcard.jpg r1 manage 279.6 K 2020-08-13 - 11:21 PeterSchmid  
JPEGjpg nucleo-dongle-sdcard2.jpg r1 manage 221.1 K 2020-08-13 - 11:21 PeterSchmid  
JPEGjpg nucleo-sd-adapter.jpg r1 manage 347.2 K 2020-06-14 - 14:52 PeterSchmid  
Unknown file formatfth prompt.fth r2 r1 manage 1.2 K 2020-08-10 - 13:19 PeterSchmid  
JPEGjpg sd-header.jpg r1 manage 75.4 K 2021-02-07 - 10:23 PeterSchmid  
JPEGjpg sd-socket.jpg r1 manage 71.7 K 2021-03-30 - 13:13 PeterSchmid  
PNGpng sdio-schematic.png r1 manage 26.8 K 2021-03-30 - 13:17 PeterSchmid  
JPEGjpg serial-flash.jpg r1 manage 82.8 K 2021-03-30 - 13:44 PeterSchmid  
Edit | Attach | Watch | Print version | History: r105 < r104 < r103 < r102 < r101 | Backlinks | Raw View | Raw edit | More topic actions
Topic revision: r105 - 2023-01-19 - PeterSchmid
 
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2024 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback