Egg Timer

SDIO

https://community.st.com/t5/stm32-mcus-products/stm32cubemx-sdio-f4/td-p/410536

Project STM32F413H_DISCOVERY FatFs_uSD_RTOS

stm32f413h_discovery_sd.c

uint8_t BSP_SD_Init(void)
{ 
  uint8_t sd_state = MSD_OK;
  
  /* uSD device interface configuration */
  uSdHandle.Instance = SDIO;

  uSdHandle.Init.ClockEdge           = SDIO_CLOCK_EDGE_RISING;
  uSdHandle.Init.ClockBypass         = SDIO_CLOCK_BYPASS_DISABLE;
  uSdHandle.Init.ClockPowerSave      = SDIO_CLOCK_POWER_SAVE_DISABLE;
  uSdHandle.Init.BusWide             = SDIO_BUS_WIDE_1B;
  uSdHandle.Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_ENABLE;
  uSdHandle.Init.ClockDiv            = SDIO_TRANSFER_CLK_DIV;
  
  /* Msp SD Detect pin initialization */
  BSP_SD_Detect_MspInit(&uSdHandle, NULL);
  
  /* Check if SD card is present */
  if(BSP_SD_IsDetected() != SD_PRESENT)
  {
    return MSD_ERROR_SD_NOT_PRESENT;
  }
  
  /* Msp SD initialization */
  BSP_SD_MspInit(&uSdHandle, NULL);

  /* HAL SD initialization */
  if(HAL_SD_Init(&uSdHandle) != HAL_OK)
  {
    sd_state = MSD_ERROR;
  }
  
  /* Configure SD Bus width */
  if(sd_state == MSD_OK)
  {
    /* Enable wide operation */
    if(HAL_SD_ConfigWideBusOperation(&uSdHandle, SDIO_BUS_WIDE_4B) != HAL_OK)
    {
      sd_state = MSD_ERROR;
    }
    else
    {
      sd_state = MSD_OK;
    }
  }
  
  return  sd_state;
}

/**
  * @brief  Initializes the SD MSP.
  * @param  hsd: SD handle
  * @param  Params : pointer on additional configuration parameters, can be NULL.
  */
__weak void BSP_SD_MspInit(SD_HandleTypeDef *hsd, void *Params)
{
  static DMA_HandleTypeDef dma_rx_handle;
  static DMA_HandleTypeDef dma_tx_handle;
  GPIO_InitTypeDef gpio_init_structure;

  /* Prevent unused argument(s) compilation warning */
  UNUSED(Params);

  /* Enable SDIO clock */
  __HAL_RCC_SDIO_CLK_ENABLE();
  
  /* Enable DMA2 clocks */
  __DMAx_TxRx_CLK_ENABLE();

  /* Enable GPIOs clock */
  __HAL_RCC_GPIOC_CLK_ENABLE();
  __HAL_RCC_GPIOA_CLK_ENABLE();
  
  /* Common GPIO configuration */
  gpio_init_structure.Mode      = GPIO_MODE_AF_PP;
  gpio_init_structure.Pull      = GPIO_PULLUP;
  gpio_init_structure.Speed     = GPIO_SPEED_HIGH;
  gpio_init_structure.Alternate = GPIO_AF12_SDIO;
  
  /* GPIOC configuration: SD_D[0..3] and SD_clk */
  gpio_init_structure.Pin = GPIO_PIN_8 | GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12;
   
  HAL_GPIO_Init(GPIOC, &gpio_init_structure);

  /* GPIOA configuration: SD cmd */
  gpio_init_structure.Pin = GPIO_PIN_6;
  HAL_GPIO_Init(GPIOA, &gpio_init_structure);

  /* NVIC configuration for SDIO interrupts */
  HAL_NVIC_SetPriority(SDIO_IRQn, 0x0E, 0x00);
  HAL_NVIC_EnableIRQ(SDIO_IRQn);
    
  /* Configure DMA Rx parameters */
  dma_rx_handle.Init.Channel             = SD_DMAx_Rx_CHANNEL;
  dma_rx_handle.Init.Direction           = DMA_PERIPH_TO_MEMORY;
  dma_rx_handle.Init.PeriphInc           = DMA_PINC_DISABLE;
  dma_rx_handle.Init.MemInc              = DMA_MINC_ENABLE;
  dma_rx_handle.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD;
  dma_rx_handle.Init.MemDataAlignment    = DMA_MDATAALIGN_WORD;
  dma_rx_handle.Init.Mode                = DMA_PFCTRL;
  dma_rx_handle.Init.Priority            = DMA_PRIORITY_VERY_HIGH;
  dma_rx_handle.Init.FIFOMode            = DMA_FIFOMODE_ENABLE;
  dma_rx_handle.Init.FIFOThreshold       = DMA_FIFO_THRESHOLD_FULL;
  dma_rx_handle.Init.MemBurst            = DMA_MBURST_INC4;
  dma_rx_handle.Init.PeriphBurst         = DMA_PBURST_INC4;
  
  dma_rx_handle.Instance = SD_DMAx_Rx_STREAM;
  
  /* Associate the DMA handle */
  __HAL_LINKDMA(hsd, hdmarx, dma_rx_handle);
  
  /* Deinitialize the stream for new transfer */
  HAL_DMA_DeInit(&dma_rx_handle);
  
  /* Configure the DMA stream */
  HAL_DMA_Init(&dma_rx_handle);
  
  /* Configure DMA Tx parameters */
  dma_tx_handle.Init.Channel             = SD_DMAx_Tx_CHANNEL;
  dma_tx_handle.Init.Direction           = DMA_MEMORY_TO_PERIPH;
  dma_tx_handle.Init.PeriphInc           = DMA_PINC_DISABLE;
  dma_tx_handle.Init.MemInc              = DMA_MINC_ENABLE;
  dma_tx_handle.Init.PeriphDataAlignment = DMA_PDATAALIGN_WORD;
  dma_tx_handle.Init.MemDataAlignment    = DMA_MDATAALIGN_WORD;
  dma_tx_handle.Init.Mode                = DMA_PFCTRL;
  dma_tx_handle.Init.Priority            = DMA_PRIORITY_VERY_HIGH;
  dma_tx_handle.Init.FIFOMode            = DMA_FIFOMODE_ENABLE;
  dma_tx_handle.Init.FIFOThreshold       = DMA_FIFO_THRESHOLD_FULL;
  dma_tx_handle.Init.MemBurst            = DMA_MBURST_INC4;
  dma_tx_handle.Init.PeriphBurst         = DMA_PBURST_INC4;
  
  dma_tx_handle.Instance = SD_DMAx_Tx_STREAM;
  
  /* Associate the DMA handle */
  __HAL_LINKDMA(hsd, hdmatx, dma_tx_handle);
  
  /* Deinitialize the stream for new transfer */
  HAL_DMA_DeInit(&dma_tx_handle);
  
  /* Configure the DMA stream */
  HAL_DMA_Init(&dma_tx_handle); 
  
  /* NVIC configuration for DMA transfer complete interrupt */
  HAL_NVIC_SetPriority(SD_DMAx_Rx_IRQn, 0x0F, 0x00);
  HAL_NVIC_EnableIRQ(SD_DMAx_Rx_IRQn);
  
  /* NVIC configuration for DMA transfer complete interrupt */
  HAL_NVIC_SetPriority(SD_DMAx_Tx_IRQn, 0x0F, 0x00);
  HAL_NVIC_EnableIRQ(SD_DMAx_Tx_IRQn);
}

Buzzer

Buttons

Adafruit Feather STM32F405

Keypad

Display

OLED

EPD

Buttons

taskENTER_CRITICAL();

taskEXIT_CRITICAL();

LPM

app_entry.c

void Init_Exti( void )
{
  /**< Disable all wakeup interrupt on CPU1  except 
       IPCC(36), HSEM(38), 
       EXTI1, EXTI2, EXTI3, EXTI4, EXTI5, EXTI6, EXTI7, EXTI9, EXTI11, and EXTI12 for push button keys, 
       EXTI0 for Wakeup,
       EXTI10 for UART Rx 
   */
//  LL_EXTI_DisableIT_0_31(~0);
#ifndef BASIC 
  LL_EXTI_DisableIT_0_31 ( (~0) & (~(LL_EXTI_LINE_1  | LL_EXTI_LINE_2  | LL_EXTI_LINE_3
                                   | LL_EXTI_LINE_4  | LL_EXTI_LINE_5  | LL_EXTI_LINE_6
                                   | LL_EXTI_LINE_7  | LL_EXTI_LINE_9  | LL_EXTI_LINE_11
                                   | LL_EXTI_LINE_12
                                   | LL_EXTI_LINE_0  
                                   | LL_EXTI_LINE_10 
                                   | LL_EXTI_LINE_8
                                  )) );
#else
  LL_EXTI_DisableIT_0_31 ( (~0) & (~(LL_EXTI_LINE_1  | LL_EXTI_LINE_2  | LL_EXTI_LINE_3 )) ); 
#endif
  LL_EXTI_DisableIT_32_63( (~0) & (~(LL_EXTI_LINE_36 | LL_EXTI_LINE_38)) );

  return;
}

tud_task() wait for event?

STM32Cube\Repository\STM32Cube_FW_WB_V1.17.3\Projects\P-NUCLEO-WB55.Nucleo\Applications\BLE\BLE_HeartRateFreeRTOS

Low Power Timer freertos_posrt.c

hw_timerserver.c /**

• Configure EXTI module */ LL_EXTI_EnableRisingTrig_0_31(RTC_EXTI_LINE_WAKEUPTIMER_EVENT); LL_EXTI_EnableIT_0_31(RTC_EXTI_LINE_WAKEUPTIMER_EVENT);

• overlay.png:
  

Button Overlay

overlay.svg: overlay.svg

special characters

• greek https://unicode.org/charts/PDF/U0370.pdf
  • mu 03BC
  • Pi 03C0
• arrows https://unicode.org/charts/PDF/U2B00.pdf
  • <-> 2B80 2B82
  • <- 2B05
  • v 2B07
• math symbols https://unicode.org/charts/PDF/U2200.pdf
  • - 2212 002D
  • / 2215 00F7
  • X 00D7
  • +- 00B1

Press F8 to get to text mode. Click with mouse on the canvas (Inkscape lingo for page) where you want your text. You will now have the text cursor on the canvas. Press Ctrl U to get into unicode entry mode. The status line at the bottom of the Inkscape window will now show "Unicode (enter to finish)". Type 03bc which is the unicode for the µ character, then press Enter (Return), if everything went well you will now have the µ character on the canvas.

• on/off

• overlay.svg: overlay.svg

ToDos

• Rundung ab 4 Stellen z.B. 9999e fs. :.00E3
• Fehlermeldung auf OLED, patch in datastackandmacros.s Fehler_Quit und Fehler_Quit_n
• Tastenlayout anpassen
• octal word hinzufügen
• xbits entfernen
• shr etc.
• on/off, c quit

• calc-black.svg: calc-black.svg

• calc-black.png:
  

• SBC
  • STM32WB55 Dongle, part of P-NUCLEO-WB55, DigiKey 497-18384-ND
  • STM32F405

• Perfboard square grid of 0.1 inches, pads on both sides (plate-through holes), 2" x 3.5", $3

• • 128x32 pixels if it should fit into 2" x 3.5"
  • 128x64 pixels, Adafruit FeatherWing OLED - 128x64 OLED

• • Würth 430473035826, DigiKey #732-7021-1-ND, data sheet, $0.5
  • TE Connectivity ALCOSWITCH Switches 1825910-6, $0.15
  • C&K PTS 647 SN50 SMTR2 LFS, DigiKey #PTS647SN50SMTR2LFSCT-ND, smaller 4.5 x 4.5 mm, $0.2

• • Adafruit USB Micro-B Breakout Board, DigiKey 1528-1383-ND, from $1 up

• • Adafruit Micro-Lipo Charger for LiPo/LiIon Batt w/USB Type C Jack, $7

BOM

• Perfboard square grid of 0.1 inches, pads on both sides (plate-through holes), 2" * 3.5", $3
• STM32WB55 Dongle, part of P-NUCLEO-WB55, DigiKey 497-18384-ND
• OLED display
  • 128x32 pixels if it should fit into 2" * 3.5"
  • 128x64 pixels
• 35 pcs push buttons, fit in 0.4" grid
• Wires
• USB Connector e.g.
  • USB MICRO-B BREAKOUT BOARD Adafruit #1833, DigiKey 1528-1383-ND, from $1 up
  • Adafruit Micro-Lipo Charger for LiPo/LiIon Batt w/MicroUSB Jack, $7
• I2C Connector

• https://hackaday.io/contest/195949-2024-business-card-contest
• https://hackaday.com/2024/05/07/the-2024-business-card-challenge-starts-now/
• roughly 3.5 in (90 mm) by 2 in (50 mm).

Forth Calculator

+--------+--------+--------+--------+--------+
|        |        |        |        |        |
|        |        |        |        |        |
+--------+--------+--------+--------+--------+
|        |        |        |        |        |
|        |        |        |        |        |
+--------+--------+--------+--------+--------+
|        |        |        |        |        |
|        |        |        |        |        |
+--------+--------+--------+--------+--------+
| STO    | RCL    | SIN    | COS    | TAN    |
|        |        | ASIN   | ACOS   | ATAN   |
+--------+--------+--------+--------+--------+
| ENTER  |        | NEG    | EXP    | BS     |
|        |        |        |        |        |
+--------+--------+--------+--------+--------+
| CLOCK  | 7      | 8      | 9      | /      |
|        |        |        |        |        |
+--------+--------+--------+--------+--------+
| CALC   | 4      | 5      | 6      | x      |
|        |        |        |        |        |
+--------+--------+--------+--------+--------+
| SHIFT  | 1      | 2      | 3      | -      |
|        |        |        |        |        |
+--------+--------+--------+--------+--------+
| ON/OFF | 0      | .      |        | +      |
|        |        |        |        |        |
+--------+--------+--------+--------+--------+

-- Peter Schmid - 2024-05-24

Comments

<--/commentPlugin-->